Got the set this past weekend and I can see why some have described the assembly instructions as lacking. We really do like the set, having placed it in our solarium so we can sip and snack while watching birds at the feeders on our deck. Here is what I'd recommend for putting this set together. Taken step by step, its easier than it looks.
ASSEMBLY STEPS:
1) TABLE: Start with the table. It uses 3 well-marked pieces of hardware (A, D & E) for attaching the 4 legs. A short dowel at the top of each leg fits into a whole on the underside of each table corner. This part is very easy. Just follow the diagram where it shows how to arrange the washers and screws. The table can then be used to assemble the stools, but put a towel on it to protect the finish.
2) STOOL ONE: Lay one of the two stool legs (#4) down flat. Add a squarish wooden cross piece (#5) where a short dowel from it will fit into a matching hole near the top of the leg.
3) HERE'S THE TRICKY PART: Push the metal piece (F) into the only small hole on the side of wooden piece #4. Be careful to line up the hole with the hole coming in from the edge of the wooden piece. You'll see what I mean. Also keep the edge of the metal piece that has a Phillips head facing out so you can use it to twist it if needed. If the long screw (B) doesn't go into that hole, you can use a Phillips screwdriver to twist the metal piece into alignment.
4) After securing the wooden piece at one end, use the screws (C) to secure two of the long metal cross pieces (#6) to the same table leg. The metal pieces push into the only holes big enough to accommodate them.
5) Next attach the other leg (#4) to those wood and metal cross pieces to complete the bottom of the stool.
6) STOOL TWO. Steps 2-5 above.
7) ADDING THE CUSHIONS: Place the stool bottoms on their feet and wedge the nice cushions into the tops between the corners of the stool legs. They almost drop in but gets a bit tight. Push the corners in and down until they make contact with the wooden cross pieces you installed in step 2.
8) Turn the stools upside down and rest on the cushions. Drop the pointed wood screws (G) into the four holes (2 in each wooden cross piece). With some force at first, push and twist the screws in with a Phillips head. After you get some bite you don't have to push so hard. It will pull itself in and securely tighten itself to the bottom of the stool.
9) The little wooden buttons (H) you're wondering about get tapped into the holes along the legs where the screws (C) were used. Some will fall out when moving the stool. When one falls out I put a tiny drop of Elmer's glue on it to keep that from happening. I only use a drop in case I need to pop it out and tighten the screw underneath one day.
This sounds complicated, but if you take it one step at a time it's kind of fun. I was completely lost at first, but after figuring it out, I actually enjoyed the process. Just keep a close watch on each screw and washer. Count them BEFORE opening the clear plastic to make sure you started with the number needed. Only open each as you need them. They are easy to misplace.
One note about the table top. Another reviewer mentioned a small dent or nick in an edge of the table top. Ours has a small blemish, too. It doesn't stand out though. In spite of that, I'm glad to have this set, as it looks nice, is sturdy and is a good value for the price. The soft leather of the cushions looks and feels of good quality, and is comfortable. I would whole-heartily recommend this set.
Add a debit or credit card to save time when you check out
Convenient and secure with 2 clicks. Add your card
Discover similar items
& Up
Price: $100 - $500
Color: Brown
Number of Pieces in Set: 3 Pieces
Style: Classic
Table Length: 50 Inches & Under
Material: Wood
Top Brands in Home & Kitchen: Top Brands
No results available. Please adjust the filters and try again.
$281
$211List:$409.00
$138
$154List:$176.00
$129
$237
$176
$300
$286
$240
$157
$174
Top rated similar items
Page 1 of 1 Start overPage 1 of 1
From the manufacturer
Linon Home Decor Products, Inc.
Linon Home Decor Products has established a reputation in the market for providing the best trend-right products for over 50 years, while offering excellent quality, style and functional furnishing to every room.
Extraordinary Displays of Home Fashion
|
|
|
|
|---|---|---|
Excellence & Experience:Linon Home Decor Products, Inc. focuses on quality control, craftsmanship, unique finishes and timely delivery. You can buy our products with confidence, knowing that you are investing in decades of manufacturing excellence and experience. |
Award Winning Design & Quality:Linon offers a broad selection of furnishings for today’s discriminating and demanding retail environment. We offer outstanding values for every room indoors and out. We maintain a total commitment of quality, service and value that is unsurpassed in our industry. |
International Capabilities:Our furniture is sourced worldwide from Asia, Eastern Europe, Italy, Greece, and Brazil. We maintain fully staffed offices in all countries to ensure quality control measures that are state-of-the-art and the best in the business. |
|
|
|
|
|---|---|---|
Chic & Style:Linon Home Decor Products translates a modern yet chic look into any home decor. Supremely chic and easy-care collection of furniture and rugs to make striking fashion statements in any home setting or space of your choice. |
Soft & Substantial:Crafted with care, our furniture and rugs are made to last, making them a perfect plush addition to your favorite space or home. In addition, Linon offers a full line of area rugs in traditional, transitional, contemporary, flokati, and indoor/outdoor rugs. |
Functional & Fashionable:Linon Home Decor Products has established a reputation in the market for providing the best trend-right products, while offering excellent quality, style and functional furnishing to every room in the home. |
Craftsmanship at its Finest!
Linon offers a broad selection of furnishings for today's discriminating and demanding retail environment. We offer outstanding values for every room, a total commitment of quality, service and value that is unsurpassed in our industry.
Compare with similar items
This Item  Linon Brown 3-Piece Table Faux Marble Tavern Set, 42" w x 22.25" d x 36" h |  |  |  |  |  | |
| Price | — | $114.20 | -34% $64.98 List: $98.99 | $59.99 | $129.99 | $104.99 |
| Delivery | — | Get it as soon as Monday, May 20 | Get it May 20 - 24 | Get it May 15 - 17 | Get it as soon as Thursday, May 16 | — |
| Customer Ratings | ||||||
| For small spaces | ||||||
| Easy to assemble | ||||||
| Sturdiness | ||||||
| Value for money | ||||||
| Sold By | — | Amazon.com | Lamerge-US | Dkeli | Amazon.com | Yaheetech |
| size | 42"w x 22.25"d x 36"h | Onesize | 39.3" Table with 2 Stools | 35.5 "(L) x 23.5" (W) x 32 "(H) | 15.8"D w/ 2 PU stools | 47.5″L×24″ W×35.5″ H |
| material | Wood | Wood | Engineered Wood, Metal, PU | Steel, MDF veneer marble, PU leather, PVC | Metal, Wood | Engineered Wood, Iron |
| style | classic | Contemporary | Classic | Modern | Standard Seat w/o Holder | Industrial |
| number of pieces | 3 | — | 3 | 3 | — | 3 |
| weight | 49.91 pounds | 40 pounds | 29.7 pounds | 40.5 pounds | 15 pounds | 44.22 pounds |
Reviews with images
Love it! Here's how to put it together.
Got the set this past weekend and I can see why some have described the assembly instructions as lacking. We really do like the set, having placed it in our solarium so we can sip and snack while watching birds at the feeders on our deck. Here is what I'd recommend for putting this set together. Taken step by step, its easier than it looks.ASSEMBLY STEPS:1) TABLE: Start with the table. It uses 3 well-marked pieces of hardware (A, D & E) for attaching the 4 legs. A short dowel at the top of each leg fits into a whole on the underside of each table corner. This part is very easy. Just follow the diagram where it shows how to arrange the washers and screws. The table can then be used to assemble the stools, but put a towel on it to protect the finish.2) STOOL ONE: Lay one of the two stool legs (#4) down flat. Add a squarish wooden cross piece (#5) where a short dowel from it will fit into a matching hole near the top of the leg.3) HERE'S THE TRICKY PART: Push the metal piece (F) into the only small hole on the side of wooden piece #4. Be careful to line up the hole with the hole coming in from the edge of the wooden piece. You'll see what I mean. Also keep the edge of the metal piece that has a Phillips head facing out so you can use it to twist it if needed. If the long screw (B) doesn't go into that hole, you can use a Phillips screwdriver to twist the metal piece into alignment.4) After securing the wooden piece at one end, use the screws (C) to secure two of the long metal cross pieces (#6) to the same table leg. The metal pieces push into the only holes big enough to accommodate them.5) Next attach the other leg (#4) to those wood and metal cross pieces to complete the bottom of the stool.6) STOOL TWO. Steps 2-5 above.7) ADDING THE CUSHIONS: Place the stool bottoms on their feet and wedge the nice cushions into the tops between the corners of the stool legs. They almost drop in but gets a bit tight. Push the corners in and down until they make contact with the wooden cross pieces you installed in step 2.8) Turn the stools upside down and rest on the cushions. Drop the pointed wood screws (G) into the four holes (2 in each wooden cross piece). With some force at first, push and twist the screws in with a Phillips head. After you get some bite you don't have to push so hard. It will pull itself in and securely tighten itself to the bottom of the stool.9) The little wooden buttons (H) you're wondering about get tapped into the holes along the legs where the screws (C) were used. Some will fall out when moving the stool. When one falls out I put a tiny drop of Elmer's glue on it to keep that from happening. I only use a drop in case I need to pop it out and tighten the screw underneath one day.This sounds complicated, but if you take it one step at a time it's kind of fun. I was completely lost at first, but after figuring it out, I actually enjoyed the process. Just keep a close watch on each screw and washer. Count them BEFORE opening the clear plastic to make sure you started with the number needed. Only open each as you need them. They are easy to misplace.One note about the table top. Another reviewer mentioned a small dent or nick in an edge of the table top. Ours has a small blemish, too. It doesn't stand out though. In spite of that, I'm glad to have this set, as it looks nice, is sturdy and is a good value for the price. The soft leather of the cushions looks and feels of good quality, and is comfortable. I would whole-heartily recommend this set.
Top reviews from the United States
There was a problem filtering reviews right now. Please try again later.
Reviewed in the United States on August 25, 2020
Color: BrownPattern Name: Tavern SetVerified Purchase
Got the set this past weekend and I can see why some have described the assembly instructions as lacking. We really do like the set, having placed it in our solarium so we can sip and snack while watching birds at the feeders on our deck. Here is what I'd recommend for putting this set together. Taken step by step, its easier than it looks.
ASSEMBLY STEPS:
1) TABLE: Start with the table. It uses 3 well-marked pieces of hardware (A, D & E) for attaching the 4 legs. A short dowel at the top of each leg fits into a whole on the underside of each table corner. This part is very easy. Just follow the diagram where it shows how to arrange the washers and screws. The table can then be used to assemble the stools, but put a towel on it to protect the finish.
2) STOOL ONE: Lay one of the two stool legs (#4) down flat. Add a squarish wooden cross piece (#5) where a short dowel from it will fit into a matching hole near the top of the leg.
3) HERE'S THE TRICKY PART: Push the metal piece (F) into the only small hole on the side of wooden piece #4. Be careful to line up the hole with the hole coming in from the edge of the wooden piece. You'll see what I mean. Also keep the edge of the metal piece that has a Phillips head facing out so you can use it to twist it if needed. If the long screw (B) doesn't go into that hole, you can use a Phillips screwdriver to twist the metal piece into alignment.
4) After securing the wooden piece at one end, use the screws (C) to secure two of the long metal cross pieces (#6) to the same table leg. The metal pieces push into the only holes big enough to accommodate them.
5) Next attach the other leg (#4) to those wood and metal cross pieces to complete the bottom of the stool.
6) STOOL TWO. Steps 2-5 above.
7) ADDING THE CUSHIONS: Place the stool bottoms on their feet and wedge the nice cushions into the tops between the corners of the stool legs. They almost drop in but gets a bit tight. Push the corners in and down until they make contact with the wooden cross pieces you installed in step 2.
8) Turn the stools upside down and rest on the cushions. Drop the pointed wood screws (G) into the four holes (2 in each wooden cross piece). With some force at first, push and twist the screws in with a Phillips head. After you get some bite you don't have to push so hard. It will pull itself in and securely tighten itself to the bottom of the stool.
9) The little wooden buttons (H) you're wondering about get tapped into the holes along the legs where the screws (C) were used. Some will fall out when moving the stool. When one falls out I put a tiny drop of Elmer's glue on it to keep that from happening. I only use a drop in case I need to pop it out and tighten the screw underneath one day.
This sounds complicated, but if you take it one step at a time it's kind of fun. I was completely lost at first, but after figuring it out, I actually enjoyed the process. Just keep a close watch on each screw and washer. Count them BEFORE opening the clear plastic to make sure you started with the number needed. Only open each as you need them. They are easy to misplace.
One note about the table top. Another reviewer mentioned a small dent or nick in an edge of the table top. Ours has a small blemish, too. It doesn't stand out though. In spite of that, I'm glad to have this set, as it looks nice, is sturdy and is a good value for the price. The soft leather of the cushions looks and feels of good quality, and is comfortable. I would whole-heartily recommend this set.
ASSEMBLY STEPS:
1) TABLE: Start with the table. It uses 3 well-marked pieces of hardware (A, D & E) for attaching the 4 legs. A short dowel at the top of each leg fits into a whole on the underside of each table corner. This part is very easy. Just follow the diagram where it shows how to arrange the washers and screws. The table can then be used to assemble the stools, but put a towel on it to protect the finish.
2) STOOL ONE: Lay one of the two stool legs (#4) down flat. Add a squarish wooden cross piece (#5) where a short dowel from it will fit into a matching hole near the top of the leg.
3) HERE'S THE TRICKY PART: Push the metal piece (F) into the only small hole on the side of wooden piece #4. Be careful to line up the hole with the hole coming in from the edge of the wooden piece. You'll see what I mean. Also keep the edge of the metal piece that has a Phillips head facing out so you can use it to twist it if needed. If the long screw (B) doesn't go into that hole, you can use a Phillips screwdriver to twist the metal piece into alignment.
4) After securing the wooden piece at one end, use the screws (C) to secure two of the long metal cross pieces (#6) to the same table leg. The metal pieces push into the only holes big enough to accommodate them.
5) Next attach the other leg (#4) to those wood and metal cross pieces to complete the bottom of the stool.
6) STOOL TWO. Steps 2-5 above.
7) ADDING THE CUSHIONS: Place the stool bottoms on their feet and wedge the nice cushions into the tops between the corners of the stool legs. They almost drop in but gets a bit tight. Push the corners in and down until they make contact with the wooden cross pieces you installed in step 2.
8) Turn the stools upside down and rest on the cushions. Drop the pointed wood screws (G) into the four holes (2 in each wooden cross piece). With some force at first, push and twist the screws in with a Phillips head. After you get some bite you don't have to push so hard. It will pull itself in and securely tighten itself to the bottom of the stool.
9) The little wooden buttons (H) you're wondering about get tapped into the holes along the legs where the screws (C) were used. Some will fall out when moving the stool. When one falls out I put a tiny drop of Elmer's glue on it to keep that from happening. I only use a drop in case I need to pop it out and tighten the screw underneath one day.
This sounds complicated, but if you take it one step at a time it's kind of fun. I was completely lost at first, but after figuring it out, I actually enjoyed the process. Just keep a close watch on each screw and washer. Count them BEFORE opening the clear plastic to make sure you started with the number needed. Only open each as you need them. They are easy to misplace.
One note about the table top. Another reviewer mentioned a small dent or nick in an edge of the table top. Ours has a small blemish, too. It doesn't stand out though. In spite of that, I'm glad to have this set, as it looks nice, is sturdy and is a good value for the price. The soft leather of the cushions looks and feels of good quality, and is comfortable. I would whole-heartily recommend this set.
Images in this review
Reviewed in the United States on April 24, 2024
Color: BrownPattern Name: Tavern SetVerified Purchase
Reviewed in the United States on March 23, 2024
Color: BrownPattern Name: Tavern SetVerified Purchase
Reviewed in the United States on December 1, 2022
Color: WhitePattern Name: Tavern SetVerified Purchase
Top reviews from other countries
Azu Gil
No se puede armar
Reviewed in Mexico on April 8, 2024Color: BrownPattern Name: Tavern SetVerified Purchase
Atul
Main table top was damaged.Small seating table damaged.
Reviewed in Canada on October 16, 2022Color: WhitePattern Name: Tavern SetVerified Purchase
Atul
Reviewed in Canada on October 16, 2022
Images in this review
Kristin
Great little table
Reviewed in Canada on March 12, 2020Color: BrownPattern Name: Tavern SetVerified Purchase
rio
Not stable
Reviewed in Canada on October 29, 2022Color: WhitePattern Name: Tavern SetVerified Purchase
John
Looks great
Reviewed in Canada on July 5, 2019Color: BrownPattern Name: Tavern SetVerified Purchase
